CP7527 INDUCTIVECP7528 ADVANCECP7529 DIGITALTIMING LIGHTINSTRUCTIONSActron, is a Business Unit of SPX Corporation.
TDCUDC 1-616NOP 1-6OA36100DC1010IMPORTANT5. Locate the Timing Marks on the Engine· The Digital Timing Light is equipped witha flashlight feature. Pres
MEASURING ENGINE RPM(Digital Timing Light Only)1. Press and Release Button Until RPM Indicator Lights.If engine is not running or #1 spark plug is n
MEASURING INITIAL TIMING1. Follow preparation list for checkingtiming in vehicle service manual.2. Start engine and warm to operatingtemperature.3.
ADVANCE TIMING LIGHT1. Press and hold down button.2. View timing marks. Turn advance knob untilmoving mark is aligned with stationary 0 degree
SETTING INITIAL TIMINGINDUCTIVE TIMING LIGHT1. Press and hold down button.2. Loosen distributor hold down bolt and turndistributor as necessary un
3. View timing marks. Loosen distributor hold down bolt and turndistributor until moving mark is aligned with stationary 0 degreemark.4. Tighten d
CHECKING & MEASURINGCENTRIFUGAL ADVANCEINDUCTIVE TIMING LIGHT1. Leave distributor vacuum line disconnectedand plugged.2. Press and hold down but
ADVANCE TIMING LIGHT1. At distributor, leave vacuum line disconnected and plugged.2. Press and hold down button. View timing marks. Turn advancek
DIGITAL TIMING LIGHT1. At distributor, leave vacuum line disconnected and plugged.2. Push and buttons until moving mark is aligned with thestation
LEFT BLANK ON PURPOSE18
1TABLE OF CONTENTSSAFETY PRECAUTIONS ... 2TIMING LIGHTS...
MEASURING VACUUM ADVANCEChecking the vacuum advance mechanism requires a vacuum pump withgauge in addition to the timing light.INDUCTIVE TIMING LIGHT1
ADVANCE TIMING LIGHT1. At distributor, leave vacuum line disconnected and plugged. Connectvacuum pump to distributor.2. Increase engine speed to RPM s
DIGITAL TIMING LIGHT1. At distributor, leave vacuum line disconnected and plugged. Connectvacuum pump to distributor.2. Increase engine speed to RPM
DISCONNECTING TIMING LIGHT1. Turn Vehicle OFF.Disconnecting cables with vehicle engine running could resultin serious injury.2. At distributor, unplug
TROUBLESHOOTING AND CARETiming Light Flashes Randomly1. Clean Inductive Pickup ClampInside Surfaces with Soft ClothDo not allow tool to touchexhaust m
2. Slide Inductive Pickup Clamp To new spot on #1 spark plug wire3. Turn Inductive Pickup Over To opposite direction on #1 sparkplug wire4. Replace
© 2005 SPX Corporation All Rights Reserved.FULL ONE (1) YEAR WARRANTYSPX Corporation, 15825 Industrial Parkway, Cleveland, Ohio 44135, warrants tothe
SAFETY PRECAUTIONSFor safety reasons, read this manual thoroughly before operating Timing Light.Always refer to and follow safety messages and test pr
3SAFETY INSTRUCTIONSVentilation Operate vehicle in ventilated area.Moving Parts Remove Jewelry Do Not Wear Loose Clothing Tie Up Long Hair Keep H
Hot Surfaces Avoid Contact With: Exhaust Manifolds Pipes Radiator Mufflers (catalytic converters)Battery Do Not Lay Tools on Battery Do Not Tou
162/4CycleRPMAdv 7 8 11 14 12 9 13 10 14TIMING LIGHTS 16156CP7529DIGITALCP7528ADVANCECP7527INDUCTIVE5
1. Timing Light2. Lens3. Inductive Pickup Clamp4. RED Clip5. BLACK Clip6. 4-digit LED Display7. 2 Cycle Mode Indicator8. 4 Cycle Mode Indicator9. RPM
IMPORTANT1. Turn Vehicle OFF.Connecting cables with engine running could result in seriousinjury.2. At distributor, disconnect and plug vacuum line.3.
IMPORTANT4. Connect RED and BLACK Battery Clips on Negative Ground ElectricalSystems.· Connect RED to positive (+) battery post.· Connect BLACK to eng
Kommentare zu diesen Handbüchern